The place to be when you have TEA. Discuss all kinds of test equipment.
Important: Use tags for the type of equipment your topic is about.
Forum rules
Use tags for the type of equipment your topic is about. Include the "repairs" tag, too, when appropriate. If a new tag is needed, request one in the TEAdministration forum.
Everything is now working as designed, apart from the bail that snapped off when I extended it. The plastic is so brittle. At least the foot part remained intact so it still sits level. It's incredible that so few parts needed attention given that this is over 40 years old and contains a computer - something that would often doom an instrument to a decade of life at most today.
I also fixed the LF output level control on the other 2305, the ground had lifted and it was sending the output (another NE5534) into clipping, this didn't affect readings, only the LF output which had been a problem when measuring distortion using the 8903B from the LF output. Now the internal distortion measuring board works on both 2305s I don't need to do that.
Here's the AB9 board before I changed six of those blue capacitors and the NE5534
Some things are like that. There's an intermittent fault which becomes less intermittent as time goes by and systematic fault finding doesn't enable you to pin it down. It could be a cracked circuit land or dry joint, or a tant showing strange behaviour. It could be damp. A wise course I don't often take, is to put a piece of junk you've acquired in the airing cupboard for a week, to make sure it's properly dry.
I have a Racal 9009 modulation meter I picked up at the Newport rally for £2.50 about four years back. It was in a sad state and judging by the stains had been kept in a damp garage and rain had dripped on it. I had an idea the case might be some good. Anyway it was only £2.50 and had a snap diode, which would be fun to play with.
Anyway, I cleaned up parts with water damage, then checked the power lines - nothing. Perhaps a blown fuse. I removed the fuse and wire looked OK, then the end cap came off. The fuse had been damaged by water. With that replaced the voltage lines looked good. I cleaned switch contacts. I decided to feed it a signal. Nothing. I started to check with a scope against the waveforms in the manual, some were a bit odd. I checked other points in the circuit and they seemed OK. Then I checked the ones that had seemed odd, and they were as shown in the manual. So I looked at the settings and the meter and it was doing about what I expected. The bloody thing had decided to work, and every time I tried it after it was working.
Another tale is a Hameg HM1005 100MHz scope which came from the Mendips rally for a fiver. The bloke told me it didn't work, he was downsizing and it had to go. I took it home, powered it up and not a peep. I took the cover off. I eyeballed it and saw nothing obvious. I began to check out the power supply. I noticed a glow from the bottom of the screen. I fiddled with the controls and there was a trace. It needed some TLC but it pretty much worked. I think that must have been a bad contact on a plug in connector. I wiggled all the connectors and cleaned them, but none of them seemed to have problems. I may have replaced reservoir caps and a few other things but I saw no repetition.
There's something very unsatisfying about things suddenly coming to life for reasons you don't understand. Of course, you are pleased it happened and it's a lot better than tracing it to an unobtainable or expensive part, but there's a loose end waving around.
Zenith wrote: ↑Sun Nov 15, 2026 7:52 pm
A wise course I don't often take, is to put a piece of junk you've acquired in the airing cupboard for a week, to make sure it's properly dry.
The manual for the Solartron 7081 DVM recommends something similar: wrap it in a blanket, and leave it powered up for 24hours so the jnternal temperature reaches 38C or so.
That made mine noticeably more stable, after any volatiles evaporated.
tggzzz wrote: ↑Sun Nov 15, 2026 9:04 pm
The manual for the Solartron 7081 DVM recommends something similar: wrap it in a blanket, and leave it powered up for 24hours so the internal temperature reaches 38C or so.
That made mine noticeably more stable, after any volatiles evaporated.
That's from the days when manufacturers knew what they were doing, why they were doing it, and weren't afraid to say so, knowing that anyone attempting to copy would have a very hard struggle.