Beware PSU current limits...

The place to be when you have TEA. Discuss all kinds of test equipment.

Important: Use tags for the type of equipment your topic is about.
Forum rules
Use tags for the type of equipment your topic is about. Include the "repairs" tag, too, when appropriate. If a new tag is needed, request one in the TEAdministration forum.
Post Reply
User avatar
EC8010
Posts: 622
Joined: Mon Sep 08, 2025 12:41 am

Beware PSU current limits...

Post by EC8010 »

I have become used to the idea that if I want a constant current from a bench supply, I just dial the current limit to the required current then twiddle voltage to be adequate. This works on my Agilent E3648A and E3649A, and on most TTi supplies. It's a very nice way of working. A Keithley 2400 is different. Actually, everything about a Keithley 2400 is different, inconsistent, or just plain awkward. But if you can get over that, it's very capable. With a 2400, you have to explicitly tell it to be a voltage or current source, then you set compliance. And that turns out to be better...

The picture shows three stacked tag boards carrying a total of ninety nine Zeners. I have traditionally tested that I've wired such things correctly by setting the 2400 to 3mA and compliance to 210V. I can then check that I get the expected voltages at various points. But a 2400 only goes to 210V and I needed 300V, so I stacked a pair of TTi PLH250 and set the current limit to 3mA. This has worked fine before. But today, I didn't gently wind the voltage up, I dabbed it whilst watching the voltmeter. It turns out that the output capacitor (charged to umpty-ump volts) is capable of converting an entire series string of thirty eight Zeners into a short-circuit. That was an entire tag board that had to be thrown away and remade. Naturally, it was the bottom board (most difficult to get at) that was totally immolated, plus five more on the middle board. I was not pleased.

So, be warned. If you want to use a bench supply in constant current mode to test Zeners, set the current limit and gently wind the voltage up from zero. Do not dab it or switch the output on.

The remade (and very carefully checked) stack has gone into a die-cast aluminium box, been filled with white oil, had silicone sealant intended for engines applied to mating surfaces, and lid screwed down. I'll give it a day or so for the sealant to go off before disturbance and measurements.

Oh, and the feed through connectors are at Stage 2 of the dreaded "Won't solder" disease. When scraped back to bare brass, they just about soldered, but they didn't wet properly. Naturally, these are the feed throughs that I have plenty of. I have seen valve socket, solder tags, and connectors that have caught this disease. It's always tinned brass that is afflicted. Has anyone else seen this?
You do not have the required permissions to view the files attached to this post.

Tags:
tggzzz
Posts: 2833
Joined: Sat Oct 22, 2022 8:17 pm

Re: Beware PSU current limits...

Post by tggzzz »

Oh, yes indeed :(

https://entertaininghacks.wordpress.com ... behaviour/ gives examples of that. Some PSUs behave well, but it shows examples where a current limited PSU delivers 170 times the set power, current limits are ignored for 500ms, and don't reach the correct value for 1500ms.

3000µF output capacitance doesn't help!
User avatar
Specmaster
Posts: 1229
Joined: Sat Oct 22, 2022 8:13 pm
Location: Chelmsford, UK

Re: Beware PSU current limits...

Post by Specmaster »

Yes, I often see that, especially after a battery has let go, even scrapping the tag, track, etc., all the way back to bare copper. I have just ordered some special flux from AliExpress to see if that can help in that dept. It is supposed to even work on stainless steel, so here hoping, fingers crossed.
Who let Murphy in?

Brymen-Fluke-HP-Thurlby-Thander-Tek-Extech-Black Star-GW-Advance-Avo-Kyoritsu-Amprobe-ITT-Robin-TTi-Heathkit-Duratool
User avatar
EC8010
Posts: 622
Joined: Mon Sep 08, 2025 12:41 am

Re: Beware PSU current limits...

Post by EC8010 »

Please do report back if the flux works. Beware that flux is deliberately corrosive, so you're going to need to thoroughly wash it away...
User avatar
Specmaster
Posts: 1229
Joined: Sat Oct 22, 2022 8:13 pm
Location: Chelmsford, UK

Re: Beware PSU current limits...

Post by Specmaster »

Yes, I will do that. I'm also waiting on some magical solution that also removed all battery corrosion and is supposed to return contacts, etc., to their former glory. Sounds too good to be true, but we shall see. I have it on good authority that these items are now at a local airport and going through customs. Fingers crossed, it won't be long before we can find out if they work.
Who let Murphy in?

Brymen-Fluke-HP-Thurlby-Thander-Tek-Extech-Black Star-GW-Advance-Avo-Kyoritsu-Amprobe-ITT-Robin-TTi-Heathkit-Duratool
User avatar
EC8010
Posts: 622
Joined: Mon Sep 08, 2025 12:41 am

Re: Beware PSU current limits...

Post by EC8010 »

Specmaster wrote: ↑Wed Nov 18, 2026 2:46 pm I'm also waiting on some magical solution that also removed all battery corrosion and is supposed to return contacts, etc., to their former glory.
Fred Wedlock had a song about a cleaner that was effective on anything from shot silk to rusty armour plate, but the company making it couldn't think of a name, so they put it out as a staff competition. One of the lads suggested that it be called "Best Universal Grit, Grime, and Effluent Remover," and added that a suitable slogan would be, "If Daz won't clean it and Omo won't brighten it, bugger it." Sounds like you've ordered a can of Best Universal Grit, Grime and Effluent Remover.
Post Reply